With the new Teleflex SX the excellent properties of the successful Teleflex VX were transferred into a smaller, handy and portable design. The Teleflex SX is operated by the new touchscreen and the wellproven control knob functionality. The interface is shown on a sharp and very bright 10.4" display.

The Teleflex SX is specially adapted to the fast events during fault location in power cables. The easyGO operation is reduced to the important and essential steps and runs mostly fully automatically.

Special features:

ARMslide technology with 15 traces in one ARM shot
ProRange for optimised display of distant details
Support of all existing prelocation technologies
Automatic adjustment and display of cable end and fault
Compatible with all fault location systems

All advantages at a glance

»» Large 10.4" sunlight-readable colour display

»» Easiest operation by touchscreen and control

knob

»» Support of all existing prelocation technologies

»» Automatic trace analysis (cable end and fault

position indication)

»» Integrated battery

»» Top performance

»» Compatible with all fault location systems

Functions

»» ARMslide with 15 traces per ARM shot

»» ProRange technology

»» Dual phased reflectometer (TDR) with simultaneous colour display of up to 6 traces

»» Automatic adjustment and display of cable end and fault

»» High resolution by real sample rate of 400 MHz

»» Internal compensation for better details at short range

»» Large 2 GB memory for automatic storage of all data

»» USB interface for data transfer via memory stick and printer

»» Control of the SPG 40

»» Report generation in *.pdf format

The Teleflex SX supports the following

technologies:

»» Symmetrical / unsymmetrical reflection measurement

»» Difference measurement / comparison

»» Two-phase reflection measurement (TDR)

»» Optimised support of all Arc reflection methods by ?U Trigger

»» ICE (impulse current methods)

»» IFL (intermittent fault locating)

»» DECAY travelling wave method

»» ARM burning

»» Partial discharge pinpointing

Standard accessories

Recommended options

Options

»» Separation Filter TF3-1 (for the operation on life

voltages up to 600 V, CAT IV)

The Teleflex SX is available as portable, battery

operated stand-alone version but can also be

integrated in any measuring system with

19" rack mounting

More products SEBAKMT

SEBA DIGIPHONE+ ESG NT PINPOINTING ACOUSTIC PINPOINTING SET FOR STEATH FAULT LOCATION IN UNDERGROUND CABLES

• Perfect acoustic quality and noise immunity
• Automatic filtration of interfering signals
• Automatic zero calibration, no adjustments necessary
• History mode
• Acoustic and step voltage fault location in one device
• BNR technology for perfect acoustic quality and noise immunity
• Automatic filtration of interfering signals
• Automatic setting of all parameters, no adjustments necessary

SEBA KMT VLOC-5000 LINE LOCATION AND TRACER FOR UNDERGROUND PIPES AND CABLES

• Precise direction guidance with right/left arrows and guidance compass
• SiS ("Signal Select") and SD ("Signal Direction") for reliable line identification
• "Distortion Alert" for signal evaluation
• Internal GPS receiver and data storage
• Permanent depth or signal current intensity measurement

SEBA KMT BT 500 IS-1 CABLE FAULT CONVERTER

• Overload protection
• Automatic discharge
• Burning of high resistive faults
• Low- potential free voltage avoids damage to other conductors
• Adjustable current limiter

SEBA KMT HPA 100 AC HPA 130 DC BURNDOWN HIGH VOLTAGE TESTING

• Powerful test- and burning system
• Continuous testing with AC voltages up to 100 kVrms at 5 kVA
• Own noise-level below 1 pC
• Built-in overcurrent protection
• DC testing up to 130 kV with optional rectifier

SEBA KMT OWTS M60 DIELECTRIC DIAGNOSIS AND PARTIAL DISCHARGE MEASURING SYSTEM

• PD diagnosis under oscillating wave test voltage
• PD evaluation possibility and pattern recognition at the nominal voltage level
• Automatic Calibration and Joint location facility
• PD level measurement according to IEC 270 at a bandwidth of 150 ... 650 kHz
• Semi- and fully automatic PD analysing software for defect location with mapping feature
• Calculation of the cable capacitance and the tan delta value
• Simple to use and easy to handle menu-driven unit for operation of the test sequence
• Compact design; low weight

SEBA KMT HV TEST SET 50KV 80KV 110KV DC HIGH VOLTAGE TESTER

• available in three versions: 50kV 80kV 110kV DC
• Highest safety by monitoring functions and easy operation
• Quick and easy mounting with compact and simple setup
• Meeting individual needs by modular design

SEBA KMT T99/1 40KV DC HIGH VOLTAGE TEST UNIT

• generate a DC voltage of up to 40 kV
• Ideal for field application because of its low weight and compact design
• High safety due to internal discharge facility
• High flexibility with the external battery
• Over-current tripping

SEBA KMT SEBALOG CORR MULTI-CORRELATOR LOGGER FOR WATER LEAK DETECTION AND LOCATION

• Correlation with up to 8 sensors at the same time
• GPS navigation directly to the leak
• Radio communication to the sensors
• No staff needed for night measurement
• Sound velocity assistant (V-assistant)
• Unique pinpointing mode

SEBA KMT HV TESTER 25KV HIGH VOLTAGE DC TESTER

• DC output voltage of 0 - 25 kV
• Portable HV Tester
• DC and insulation testing of cables, joints, electrical fixtures, etc.
• High flexibility with built-in battery

SEBA KMT EASYTEST 20KV VFL CABLE TESTER VERY LOW FREQUENCY

• simplified version of the standard VLF test
• Easy to operate
• Configurable test sequences
• Compact, rugged and lightweight design
• AC, DC and sheath testing in one single system
• Reporting via USB or Winkis