The VM-810 location system was specifically developed to locate and determine the laying depth of metallic water pipes and gas pipes. The precisely tuned, high location frequency of 83 kHz enables the tracing of a line even across several sleeves and connection points, which generally represent a high resistance for a low frequency. The determination of depth occurs automatically at the touch of a button. The system is distinguished by its user-friendliness, its large display and large buttons as well as its extensive accessories.

Advantages

Easy to use
High location accuracy
Optimal inductive transmission of line signals
Signal "jumps over" insulating pipe sleeves

Standard accessories

Recommended options

More products SEBAKMT

SEBA SURGEFLEX SFX-15 SFX-25 CABLE FAULT LOCATING SYSTEM

• » DC-Testing up to 15 kV / 25 kV (depending on model)
• » Prelocating
• » - Reflection measurement
• » - ARM-Measurement (Arc reflection method)
• » - ICE Impulse current method
• » Cable tracing (optional)
• » Pin-pointing
• » - Distance and acoustic measurement
• » - Audio frequency methods (optional)
• » Battery and mains operation

SEBA KMT EASYLOC CAM LOCATION SYSTEM FOR LOCATION AND DEPTH MEASUREMENT OF SEWER TV CAMERAS

• 3 active frequencies (512 Hz, 640 Hz und 33 kHz)
• depth measurement at the push of a button
• Maximum marker to mark the strongest signal
• optional: Carry Bag - for easy and safe transport of Easyloc Cam
• optional: Pipeline sonde - for location non-metallic pipes

SEBA SMART THUMP 16 CABLE FAULT LOCATION SYSTEM ON LOW AND MEDIUM VOLTAGE CABLES

• 1500J at 8 / 16 kV, 16 kV DC-HV proof test 23/46mA Burning
• Integrated ARM and ICE Prelocation
• Easy Go - automatic sequence to proof test, pre-locate & pinpoint
• Automatic interpretation of test results
• Sunlight readable, transflective 5.7" TFT colour display
• Safe OP Check protects user from incorrect or faulty lead connections
• USB interface for trace export via USB flash drive

SEBA KMT MMG 10 CABLE SHEATH TESTER

• Adjustable current limiter
• Easy and powerful testing of cable jackets
• Pulsed output voltage for sheath fault pinpointing
• Burning of cable faults

SEBA SWG 500 SURGE WAVE GENERATOR FOR FAULT LOCATION IN CABLES SWG500

• Voltage Ranges : 0..2.5kV / 5kV / 10kV ; 0..4kV / 8kV / 16kV
• Energy : 195J ; 500Joules
• MAx Current Imax : 185mA ; 300mA
• Optimized surge energy for switchable capacitors
• ICE - Impulse Current Method
• ARM - Arc Reflection Method

SEBA KMT VFL CR-20 VERY LOW FREQUENCY CABLE TESTING SYSTEM

• VLF Test System 20 kV
• high test capacity of 3 µF permits the simultaneous testing of all three phases
• method is officially recommended by the two VDE Standards 0276-620 and 0276-621
• VLF is the most economic method for testing PE and XLPE cables

SEBA KMT HPA 100 AC HPA 130 DC BURNDOWN HIGH VOLTAGE TESTING

• Powerful test- and burning system
• Continuous testing with AC voltages up to 100 kVrms at 5 kVA
• Own noise-level below 1 pC
• Built-in overcurrent protection
• DC testing up to 130 kV with optional rectifier

SEBA KMT FERROLUX FLE 10 AUDIO FREQUENCY RECEIVER FOR CABLE LOCATION, SELECTION, SHEATH FAULTS

• Precise direction guidance with right/left arrows
• "SignalSelect" for clear route location
• Depth and signal current intensity measurement at the push of a button
• Route sensor weighs less than 1 kg for non-tiring use
• "DirectSignal" for effective line location

SEBA KMT PD LOC PARTIAL DISCHARGE PINPOINTING SYSTEM FOR RPECISE LOCATION OF PD FAULTS IN MEDIUM VOLTAGE CABLES

• Precise PD pinpointing in mixed cable networks
• Location of faults in joints of single core cables
• Easy handling in the ?eld

SEBA BPS 5000-D BURN AND PROOF TEST SYSTEM ON MEDIUM VOLTAGE CABLES BPS-5000D BPS500D BPS 5000D-VLF

• Easy-go single button operation
• Protocolling of the test results
• Data transfer via Bluetooth
• DC burn current up to 6 A
• AC burn current up to 110 A
• Sheath fault pinpoiting mode