In accordance with most regulations, cables and joints must be tested after installation or repair. For this test the breakdown strength of the cable is tested.

The portable VLF Test System 20 kV of Seba KMT can be used to test the cables in conjunction with the according local regulations for operating voltage levels up to 11 kV for new cables and 16 kV for aged cables at 3 µF cable capacity.

By using the patented Seba KMT 0.1 Hz Cosine Square Wave Voltage, weak and for further operation critical spots in PE, XLPE but also in paper cables are brought to a controlled breakdown very fast without causing additional damage or ageing to the cable insulation.

The weight of 50 kg make the VLF Test System 20 kV a powerful, universal and at the same time portable unit.

_ The patented change over principle in combination with

the recycling of energy stored in the cable capacity

results, in comparison to other methods, in a lower

weight, less energy consumption and much higher test

capacity.

_ The high test capacity of 3 µF permits the simultaneous

testing of all three phases.

_ The method is officially recommended by the two VDE

Standards 0276-620 and 0276-621.

_ Independent researches shows that VLF test is done

most effectively with the 0.1 Hz cosine square wave

shape compared to any other VLF wave shape or

frequency.

_ VLF is the most economic method for testing PE and

XLPE cables. DC test is not applicable for these cable

types.

_ controlled output voltage

Standard accessories

Scope of Delivery

_ Basic unit

_ AC mains cable

_ Earthing cable 4 m

_ HV-connection cable 4 m

_ Accessory bag

_ Operating manual

Recommended options

Options

_ Breakdown recognition and automatic shut-down.

_ VLF / DC leakage current measurement

More products SEBAKMT

SEBA KMT LPD MONITOR ON-LINE PD PARTIAL DISCHARGE MONITORING SYSTEM FOR MV AND HV

• Portable online PD measuring system for monitoring MV and HV systems
• 16 channels
• Allows ef? cient forward planning of necessary maintenance work
• Quick and easy to install
• Integrated automatic knowledge-based evaluation of measured PD levels
• Current status can be viewed at any time via remote access

SEBA KMT GEOLUX GL 660-1 EARTH FAULT LOCATOR FOR FAULT LOCATION IN ISOLATED, EARTH FREE SYSTEMS

• Earth fault locator for fault location in isolated, earth free systems
• Mains filter for direct coupling to live cables up to 660 V
• Pulsed output current for easier detection of the test signal
• Filter for the suppression large interference signals
• Location of earth faults up to 150 kOhm
• No switch off during the fault location required
• No influence to the signal lines connected to

SEBA SMART THUMP 16 CABLE FAULT LOCATION SYSTEM ON LOW AND MEDIUM VOLTAGE CABLES

• 1500J at 8 / 16 kV, 16 kV DC-HV proof test 23/46mA Burning
• Integrated ARM and ICE Prelocation
• Easy Go - automatic sequence to proof test, pre-locate & pinpoint
• Automatic interpretation of test results
• Sunlight readable, transflective 5.7" TFT colour display
• Safe OP Check protects user from incorrect or faulty lead connections
• USB interface for trace export via USB flash drive

SEBA TELEFLEX T3060 SINGLE-PHASE POWER CABLE REFLECTOMETER T 3060

• Range 8 km, 64 km (for ICE and Decay only)
• Fully equipped reflectometer with cursor, gain, and range adjustment
• High-contrast 5.7’’ TFT color display (640 x 480 pixel), with LED backlight
• Single-phase ARM input with ICE, Decay and Trigger
• AC or battery operated (up to 3 hours battery life)

SEBA KMT HPG 50..80-D DC & AC HIGH VOLTAGE CABLE TESTER

• HPG 50-D, AC testing up to 35 kVRMS/ DC testing up to 100 kV
• HPG 70 / 80-D, AC testing up to 50 / 58 kVRMS / DC testing up to 140 / 150 kV
• Suitable for AC testing and DC testing
• Compact, cast-resin high-voltage transformers
• Separate control and HV-units
• Voltage continuously adjustable
• Powerful system: 1,2 kVA continuous operation, up to 3 kVA 60 min. short-time operation

SEBA KMT HV TESTER 25KV HIGH VOLTAGE DC TESTER

• DC output voltage of 0 - 25 kV
• Portable HV Tester
• DC and insulation testing of cables, joints, electrical fixtures, etc.
• High flexibility with built-in battery

SEBA TELEFLEX SX CABLE REFLECTOMETER FOR FAULT LOCATION MEGGER

• ARMslide technology with 15 traces in one ARM shot
• ProRange for optimised display of distant details
• Support of all existing prelocation technologies
• Automatic adjustment and display of cable end and fault
• Compatible with all fault location systems

SEBA KMT HPA35 HPA50 HPA58 HPA78 AC HIGH VOLTAGE HIPOT TESTING WITHSTANDING

• HPA 35, AC testing up to 35 kVrms
• HPA 50 / 58 AC testing up to 50 / 58 kVrms
• HPA 78, AC testing up to 78 kVrms

SEBA KMT EASYTEST 20KV VFL CABLE TESTER VERY LOW FREQUENCY

• simplified version of the standard VLF test
• Easy to operate
• Configurable test sequences
• Compact, rugged and lightweight design
• AC, DC and sheath testing in one single system
• Reporting via USB or Winkis

SEBA KMT VLOCML2 PIPELINE LOCATION AND TRACING FOR UNDERGROUND PIPES AND CABLES

• Location of passive markers which are used by utility
• companies for labelling underground lines
• Colour-coded display of the signal strength
• Specifi c line location mode
• Specifi c marker location mode
• Mode for simultaneous location of lines and markers