Set identificare faza cabluri impamantate sau scurtcircuitate medie tensiune Seba PIL 8 Phasenlux

Cod: Seba-KMT PIL-8 Phasenlux


 

Brosura produs , 0.33 Mb

Descriere

Pil 8

The Phase identification System PIL 8 permits a fast and especially safe phase determination at the jointing location during the mounting of medium voltage cables. 

According to DIN VDE 0105 0100 part 2 (EN 50110-1) from Okt. 1997, Pos. 6.2.4.1 Topic 3 (Page 12) it specifies : 

"... If the earthing or shorting has to be removed for the duration of measurements or tests, suitable other safety measures have to be taken." 

Such safety measures require a relatively large effort and are not always practical. The specific advantage of the technology used in the PIL 8 is the fact, that the ground or shorting must not be removed. In opposition, this grounding it is an essential part of the procedure, which means, the cable must be grounded and shorted for the system to work. Resulting the use is absolutely safe. For each phase the according transceiver clamp are installed tot he grounded cable end and then at the selection point each phase is identified and marked. 

Key benefits:

  • Maintenance free transceiver clamps
  • Suitable for any type of switch gear
  • Requires only one person
  • Easiest operation
  • Absolute safe phase identification

 

 

Accesorii standard

Scope of delivery

1 pc. Generator/receiver PIL 8

1 set of Cables VL 83-E

3 pairs of Transceiver tongs PIZ 50

1 pc. Transport case PIK 8

 

Special accessories

for each additional end-to-end measurement (3 are

possible) 3 pairs of transceiver tongs PIZ50

 

Optiuni recomandate

 

 

Alte produse SEBAKMT

CONVERTOR DEFECTE INALTA IMPEDANTA CABLURI DE CONTROL, SEMNALIZARE SEBA BT 500 IS-1

• Protectie la suprasarcina
• Sistem de descarcare automata
• Pentru conversia defectelor cu impedanta ridicata de pe cablurile de semnalizare, control sau telecomunicatii

 

SISTEM INCERCARE SI LOCALIZARE DEFECTE CABLE SEBA SURGEFLEX SFX-32

• Încercare cu pâna la 32 kV
• Prelocalizare:
• o Masurarea impulsului reflectat
• o ARM® (Metoda reflexiei arcului)
• o Metoda cuplarii în curent 8 / 16 / 32 kV
• Ardere (modificarea defectului) pâna la 32 kV
• Localizarea traseului (optional)
• Localizare exacta: o Masurarea distantei / câmpului acustic(8 / 16 / 32 kV cu 1750 / 3500 J)
• o Localizarea defectelor de manta (0 … 5 kV cu limitare în curent)

 

GENERATOR UNDA DE SOC MEDIE SI INALTA TENSIUNE LOCALIZARE DEFECTE CABLU SEBA T18/5

• Domenii tensiune : 0..3kV / 0..6kV / 0..12kV
• Energie : 1000 Joule


LOCATOR DE TRASEE CABLURI SI CONDUCTE SUBTERANE SEBA VLOC-9800

• Clearly laid out user interface
• Automatic or manual amplification options
• Depth and amperage at the press of a button
• Distance Sensitive Left/Right GuidanceTM
• Sheath fault location (optional)

 

APARAT INCERCARE MANTA CABLURI MEDIE SI INALTA TENSIUNE SEBA MMG 10

• Încercarea mantalei cablurilor de medie si înalta tensiune
• Prelocalizarea si localizarea exacta a defectelor
• Conversia defectelor cu rezistenta mare de pe cablurile de joasa tensiune

 

LOCALIZARE DEFECTE CU PUNERE LA PAMANT IN SISTEME IZOLATE FARA IMPAMANTARE SEBA GEOLUX GL 660-1

• Earth fault locator for fault location in isolated, earth free systems
• Mains filter for direct coupling to live cables up to 660 V
• Pulsed output current for easier detection of the test signal
• Filter for the suppression large interference signals
• Location of earth faults up to 150 kOhm
• No switch off during the fault location required
• No influence to the signal lines connected to

 

GENERATOR UNDA DE SOC PENTRU LOCALIZAREA DEFECTELOR IN CABLURI SEBA SWG 500

• Domenii tensiune : 0..2.5kV / 5kV / 10kV ; 0..4kV / 8kV / 16kV
• Energie : 195J ; 500Joul
• Curent maxim Imax : 185mA ; 300mA
• Energie de soc optimizata prin condensatoare comutabile
• ICE - Metoda cuplarii în curent(ICE = Impulse Current Equipment)
• ARM - Metoda reflexiei pe arc(metoda de reflexie cu IT)

 

TRUSA INCERCARE CU TENSIUNE MARITA C.C. SEBA HV TESTER 25KV

• DC output voltage of 0 - 25 kV
• Portable HV Tester
• DC and insulation testing of cables, joints, electrical fixtures, etc.
• High flexibility with built-in battery

 

PUNTE MASURA DEFECTE CABLURI RETELE COMUNICATII SEBA KMK 8

• Integrated Reflectometer (TDR)
• Active bridge for high precision R and C measurements and DC and AC fault location
• Measurement by Graaf method in connection with an active slave at the far end
• Passive Wheatstone bridge for R and C measurements and DC and AC fault location
• Test Systems for Pre-measurement, Quick test and Quality testing
• Measurement of interference voltages
• Warning and information system
• Remote control for the operation of the electronic far end loop control switch

 

LOCATOR DE TRASEE TEVI, CABLURI SI CONDUCTE INGROPATE SEBA EASYLOC RXTX

• Moduri de lucru: Retea, Radio si Activ
• Control semiautomat al sensibilitatii
• Masurarea adâncimii în modurile active si pasive
• Afisarea intensitatii semnalului
• Compatibil cu sistemele existente cu 8,44** si 33kHz
• Generator de putere de înalta clasa