The T 26/1A and T 26/1B high-voltage test sets are efficient, mobile systems for high-voltage testing of cables, cable systems and installations as required by current regulations (VDE) with DC voltages of up to 400 kV and 650 kV respectively. The sets are suitable for both installation in measuring trailers and onsite testing as stationary test set. The spatial separation of the operating and high-voltage units makes it possible to operate the sets from outside the immediate danger area. Their modular structure makes them easy to set up on site and allows adaptation to measuring tasks.

The sets are primarily designed for power supply companies, cable laying firms and cable manufacturers for the DC voltage testing of high-voltage systems and cables. Their short-circuit-proof output circuit and high power make them suitable for use in fault location as a burn-down unit for burning high-impedance and intermittent cable fault.

Key benefits:

Great mobility
Simple, safe operation
Thermal overload shutdown
Discharge switch

Standard accessories

Recommended options

More products SEBAKMT

SEBA KMT OWTS M60 DIELECTRIC DIAGNOSIS AND PARTIAL DISCHARGE MEASURING SYSTEM

• PD diagnosis under oscillating wave test voltage
• PD evaluation possibility and pattern recognition at the nominal voltage level
• Automatic Calibration and Joint location facility
• PD level measurement according to IEC 270 at a bandwidth of 150 ... 650 kHz
• Semi- and fully automatic PD analysing software for defect location with mapping feature
• Calculation of the cable capacitance and the tan delta value
• Simple to use and easy to handle menu-driven unit for operation of the test sequence
• Compact design; low weight

SEBA SURGEFLEX SFX 8-1000 CABLE FAULT LOCATING SYSTEM

• Small, light and portable
• Very low voltage levels
• Complete fault location with DC Testing up to 8 kV
• Prelocation with ARM and ICE
• Burning with up to 1.4 A

SEBA KMT HPG 50..80-D DC & AC HIGH VOLTAGE CABLE TESTER

• HPG 50-D, AC testing up to 35 kVRMS/ DC testing up to 100 kV
• HPG 70 / 80-D, AC testing up to 50 / 58 kVRMS / DC testing up to 140 / 150 kV
• Suitable for AC testing and DC testing
• Compact, cast-resin high-voltage transformers
• Separate control and HV-units
• Voltage continuously adjustable
• Powerful system: 1,2 kVA continuous operation, up to 3 kVA 60 min. short-time operation

SEBA KMT CI LCI CABLE IDENTIFIER TEST SET

• Inexpensive cable selection system
• Easy to operate
• Safe handling
• Very small

SEBA KMT HV TEST SET 50KV 80KV 110KV DC HIGH VOLTAGE TESTER

• available in three versions: 50kV 80kV 110kV DC
• Highest safety by monitoring functions and easy operation
• Quick and easy mounting with compact and simple setup
• Meeting individual needs by modular design

SEBA T18/5 SURGE WAVE VOLTAGE GENERATOR FOR CABLE FAULT LOCATING

• Voltage Ranges : 0..3kV / 0..6kV / 0..12kV
• Energy : 1000 Joules

SEBA BPS 5000-D BURN AND PROOF TEST SYSTEM ON MEDIUM VOLTAGE CABLES BPS-5000D BPS500D BPS 5000D-VLF

• Easy-go single button operation
• Protocolling of the test results
• Data transfer via Bluetooth
• DC burn current up to 6 A
• AC burn current up to 110 A
• Sheath fault pinpoiting mode

SEBA KMT SEBALOG CORR MULTI-CORRELATOR LOGGER FOR WATER LEAK DETECTION AND LOCATION

• Correlation with up to 8 sensors at the same time
• GPS navigation directly to the leak
• Radio communication to the sensors
• No staff needed for night measurement
• Sound velocity assistant (V-assistant)
• Unique pinpointing mode

SEBA KMT VFL SINUS 54KV SINE WAVE CABLE TEST SYSTEMS

• High test capacity of 5 µF
• Single-button operation "easyGo"
• Continuous duty cycle
• Integrated safety system
• Suitable for diagnosing 45 kV rated cables

SEBA KMT VM-810 LOCATION UNDERGROUND PIPES AND CABLES

• Easy to use
• High location accuracy
• Optimal inductive transmission of line signals
• Signal "jumps over" insulating pipe sleeves